LiFePO4 Battery, 12V 5Ah

LiFePO4 Battery: 12V 5Ah with LED Indicator.
Variant price modifier:
Base price with tax
Salesprice with discount
Tax amount
Price / kg:



  • 12.8V 5Ah LiFePO4 rechargeable battery 
  • Build in PCB to protect battery from overcharged and discharged
  • LED indicator shows battery capacity status: Full, Mid or Low
  • Voltage: 12.8 V (working)   15.2 V (peak)  9.6 V ( cut-off)
  • Nominal: 12V
Capacity 5Ah±5% 0.05C20A discharge,25’C
Cycle life >1000 cycles ( @ 0.2C rate, IEC Standard) Running 5 times more than SLA battery
  • One  PCB  installed with the battery pack and protects the battery from
    • Overcharge       (>15.6V)
    • Over discharge  (
    • Over drain ( >40~60 Amp)
    • Short circuits
Terminal T1 
Charging rate 2.5A  Max
Max. Discharging Rate 10A Max  (2.0C rate)
Dimensions(LxWxH) 90mm (3.5 ") X 70mm (2.8") x 101mm (3.98") Connector tabs are additional
Weight 670grams (1.0lbs 7.6Oz)
  • Charge Current Standard:0.2 C;Max: 0.5C Working temperature:0~45 ℃
  • Charge cut-off Voltage: 15.2±0.05V
  • Discharge Current:  Standard 0.05 C;Max 2 C, Working temperature:25 ℃
  • Impedance ≤50mΩ, 50% SOC at 25 ℃
  • Weight Approx: 0.67kg
  • Dimension(mm) 90×70×101 Approx
  • Passed UN38.3 certification testing

PERFORMANCE: Charge battery pack with specific charger, 0.2 C constant Current/constant voltage to 15.0V at 23±2 ℃.

  • Capacity: After standard charging, let sit for 0.5h, then discharge at 0.05C to voltage 9.6V, recording the discharging time, which should be ≥20 h.
  • 1C Capacity: After standard charging, let sit for 0.5h, then discharge at 1C to voltage 9.6V, recording the discharging time, which should be ≥51min.
  • 10℃ Capacity: After standard charging, place battery in -10℃ for more than 4h, then discharge at 0.05C to voltage 8.0V recording the discharging time, which should be ≥12h.

PCB Parameters:

  •  Over charged Protect Voltage 3.90± 0.025V
  • Over charged Protect Delay time 0.5S-1.5S
  • Over charged Protect Relieve Voltage 3.80 ± 0.05 V 
  • Over Discharged Protect Voltage 2.20± 0.08 V
  • Over Discharged Protect Delay time 50mS-150mS
  • Continuous discharge current ≤20A
  • Over Current Protect 40-60A
  • Over Current Protect Delay 5mS-150mS
  • Over discharge release conditions ≥2.7V 
  • Protection plate static power consumption <50µA


  • Do not immerse the battery in water or allow it to get wet.
  • Do not use any chargers other than those recommended
  • Do not reverse the positive(+) and negative(-) terminals.
  • Do not connect the battery directly to wall outlets or car cigarette-lighter sockets.
  • Do not put the battery into a fire or apply direct heat to it.
  • Do not short-circuit the battery by connecting wires or other metal objects to the positive(+) and negative(-) terminals.
  • Do not pierce the battery casing with a nail or other sharp object, break it open with a hammer, or step on
  • Do not strike, throw or subject the battery to sever physical shock.
  • Do not directly solder the battery terminals.
  • Do not place the battery in a microwave oven or pressurized container.
  • Do not use the battery in combination with primary batteries(such as dry-cell batteries) or batteries of different capacity, type or brand.
  • Do not use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal in any way. If the battery is in use or being recharged, remove it from the device or charger immediately and discontinue use. 

SHIFT Electric Vehicles is free of any responsibility with the contingency and loss due to incorrect use of the batteries.